MemCard – PCMCIA Expansion

Tech Specs:
- Measures 3.6×2.3×0.7inches
- Power: 20 mA @ 5V
- Power input: regulated 5V, or +8.5V w/ on-board linear regulator
- Temperature: -40 to +85 Celsius
- 68-pin PCMCIA ATA Flash cards up to 420 MB
- Up to 6 24-bit ADCs (LTC2400)
- 2.5 V reference, temperature sensor
- Up to 33 ch. 12-bit ADC (TLC2543)
- RS-232 drivers and 5V regulator
- 10 BASE-T RJ45 Ethernet interface (CS8900)
Similar expansion boards: FlashCore-B, P50, OP-A
Supported controllers: i386-Engine/IE-P, A-Engine/AE-P, A-Engine86/AE86-P, V25-Engine-LM,A104, Birdbox-A, I-Drive, 586-Engine, TD86, 586-Engine/IE-P
General Info
With a 68-pin PCMCIA-ATA interface, the MemCard supports Flash cards up to 220 MB from SanDisk, and M-Systems. 5V Flash memory chips (128/512 KB each) are also available for non-removable data storage. It provides I/O mapping access and interrupt support for PCMCIA I/O cards.
These credit-card-sized 68-pin cards can be used as portable data carriers and provide a reliable and efficient method to transfer useful data or programs among embedded controllers, PCs, and different systems. With TERN’s software support, you can access any of the sectors within the Flash card memory. An optional ejecting mechanism is also available.
Up to six 24-bit ADC (LTC2400) chips, each providing one channel of 0-2.5V analog inputs, can be installed. The LTC2400 is a 24-bit analog-to-digital converter with an integrated oscillator. It uses delta-sigma technology, providing a typical conversion time of 160ms.
The MM uses a 2.5V precision reference (LT1019-2.5) for the 24-bit ADC. The LT1019 has a typical ultra-low temperature drive of 3ppm/C and a built-in temperature sensor. For applications that use thermocouples, the LT1019 can be used to measure board or ambient temperatures.
Up to three TLC2543 chips can also be installed, providing a total of 33 12-bit ADC inputs. The 12-bit ADC has sample-and-hold, a high-impedance reference input, 11 single-ended 0-5V (or 0 to REF) inputs, and a 10 kHz sample rate while driven by a 40 MHz A-Engine.
An Ethernet LAN controller (CS8900, Crystal Semiconductor Corporation) can be installed on the MM. The CS8900 includes on-chip RAM and 10BASE-T transmit and receive filters. The CS8900 directly interfaces to the TERN controller’s data bus, providing high-speed, full duplex operation. A standard RJ45 8-pin connector can be installed for the Ethernet LAN connection.
Due to mechnical constraints, the Ethernet RJ45 connector and the 68-pin PCMCIA socket cannot be installed at the same time on the MM. A flat cable with an off-board Rj45 may be connected to the MM if the PCMCIA socket is installed.
MemCard – PCMCIA Expansion
Does not include add-on options or controller.
Add-on Options
- 68-pin PCMCIA socket with PAL
- Ejecting mechanism
- 24-bit ADC w/ 2.5V REF (up to 6)
- Reference 20 ppm/C 2.5V
- 11 ch. 12-bit ADC (up to 3)
- RS-232 driver & 5V regulator
- Ethernet interface (CS8900)
- PCMCIA ATA cards: 2MB to 240 MB
NOTE: If PCMCIA is installed, RJ45 must be off-board, connected via flat cable.
Related Products


