CANblue II
Active Bluetooth interface/bridge
1 x CAN (High-Speed)
The CANblue II is a reasonably priced and versatile CAN Bluetooth module, which can be used in a wide range of applications due three supported operation modes.
For service applications it enables e.g. the wireless access to CAN systems using the standard Bluetooth interface provided within many notebooks. Due to this, diagnostic data can be read or system configuration tasks can be performed very simple and flexible, even at components which are hard to reach.
Using several CANblue II devices network segments can be networked among each other. This enables the reliable connection of rotating or moving parts, e.g. in wind turbines, as well as the bridging of larger distances between different sub-systems up to 200 meters. Failure-prone slip ring connections or expensive installations of large CAN lines can such be avoided.
Not least, the Bluetooth-based communication also offers significant advantages in terms of range and noise immunity, compared to traditional WLAN solutions.
Features and benefits
- Quick start-up and connection
- High transmission range
- Low latency transmission and high data throughput
- Flexible configuration options (combination of several CANblue II)
How It Works
Bridge mode
The bridge mode allows the user to set-up a CAN-Bluetooth-CAN bridge by using two CANblue II devices. Message exchange occurs on layer 2 and is transparent. The device can also be used in systems with CANopen, DeviceNet or customer-specific protocols. CAN-ID filters can be set for data exchange via Bluetooth. Using more than 2 CANblue devices, multiple busses can be linked with each other.
ASCII/Binary protocol mode
In this mode, functions for transmitting and receiving CAN messages and for configuring the CANblue II are available to the user based on simple ASCII commands and optimized CAN binary messages. The CANblue II is ideal for “non-Windows” systems or embedded platforms.
PC operation mode with VCI driver support
Because it is supported by the VCI CAN driver, the CANblue II can be operated with all IXXAT tools and with customer-specified programs. In addition, wireless access to CAN systems via Bluetooth can also be easily achieved with existing VCI-based application programs and tools.
Accessories
For the CANblue II variant with external antenna
Antenna
Stub antenna with RPSMA plug, 90 degree tiltable. (Technical data: Length 10 cm, 1 dBi, 2,4 Ghz, 50 Ohm impedance , half wave dipole, linear polarization.)
Magnetic foot antenna
Antenna with a strong magnetic foot for mounting, 1,5 m cable and RP-SMA connectors. (Technical data: Weight 109 g, diameter 47 mm, height 45 mm, designed for indoor use or outdoor use, provided that the antenna is protected against water and moisture.)
Screwable antenna foot
Screwable antenna foot with 2 m cable and RP-SMA connectors. (Technical data: Weight 80 g, diameter 28 mm, height 20 mm, diameter of the mounting hole 20 mm + 0.2 mm, designed for indoor use or outdoor use, provided that the antenna is protected against water and moisture.)
Technical specifications
| Bluetooth interface | Bluetooth v4.0 with EDR, 200 m max. transmission range |
| Microcontroller | 32-bit microcontroller |
| CAN controller | CAN 2.0 A/B |
| CAN bus interface | ISO 11898-2, Sub D9 plug according to CiA 303-1 |
| Galvanic isolation | 1 kV, 1 sec. |
| Power Supply | 9 – 30 V DC, 0.6 W |
| Temperature range | -40 °C to +85 °C |
| Sending delay (average) | approx. 4 ms (in Shortest Latency Mode) |
| CAN performance at 1 Mbit | 100 % bus load |
| Certification | CE, FCC, Telec |
| Housing | Plastic housing with mounting holes |
| Protection Class | IP20 |
| Size | 82 x 64 x 26 mm |
Contents of delivery
- CANblue module and user’s manual
- CAN driver VCI for Windows
- Simple CAN tool “canAnalyser Mini”
Order number
Order number accessories
(for the CANblue II variant with external antenna)
Accessories
